shogun univ mod 3d models

If you find the Key-Bak can still move inside the enclosure when it is completely closed, put some foam tape in there with it to keep it from rattling. Once installed, the enclosure should clear the lower rear belt by ~3 mm. If you have problems with...

This is fairly inexpensive and elegant setup. Plan to use Quanum Overlord Diversity on top of the tripod and this module on the side of the tripod connected to Quanum Overlord or another ground station. The DVR in my Fat Shark goggles stopped working...

-Towers Tray = Same mods and settings as the Figures Tray. I figured I would take out the extra step up around the towers too again just to save on unnecessary plastic even though the original feature does look cool. Give and take. -Bottom Row...

instead other models of TMCxxx , No solder iron necessary, you just have to rotate the connectors receptacles on the motherboard with a simple leatherman tool.like on this video Be care, some of the latest motherboard doesn't have support under the...

I also want to do other mods. Maybe come up with a battery tray to use the stock battery holder for the brackets, maybe a cable comb to organize the front motor wires and sensor cable as they run along the top brace. and probably some sort of system...

One here on printables linked with this model and other on thingiverse: https://www.thingiverse.com/thing:4934774I made some changes to the original thingiverse model:the thingiverse model was not based on this crates here on printables  and...

and a 7 inch 1/2 ID petg barrelaverage of 84.9 fps with 20 Dart Zone sureshot darts with a stock Kronos spring and a stock nexus barrel (5.75" .527 barrel)Credit to Olaveta for the basic framework for this...

Please note that when mounting the tensioner, it's recommended to turn it around 180 degrees so that the tensioner extends towards the rear of the printer (opposite to attached pictures), especially if you have any mods on the hotend (cable guides...

Also, here are the original Fusion 3D Designs in case someone would like to fork/improve/mod this: 80mm Fan Mating: https://a360.co/32NUbec 92mm Fan Mating: https://a360.co/2BMxdIC Filter Box Base : https://a360.co/36a0Y3W Filter Box :...

As I had already printed the drawers and drawer casings and they were a long print, I elected to instead design these mods to ship the linear rails slightly upward to clear the drawers. These adapters will attach to either side of the rails and will...

... and grounds between multiple interfaces. In order to take full advantage of the Duet features I designed the [CR-10S Pro Custom Transfer Board](https://github.com/ReXT3D/cr-10s-pro-mods/tree/duet3d) that allows all signals to be fully independent.

This fan duct is designed specifically to fit an e3d/j-head v6 hotend from this mod: https://www.thingiverse.com/thing:2772682. Several modifications are applied to this design: 1. The blower fan hole is adjusted to accommodate a 50x20 mm blower...

You'll lose roughly 20mm of Z travel by doing this mod. If you're running my Y gantry mounts, they were designed to lift Z with this modification in mind and you can reclaim some of that travel. ... It's a good idea to test out your actual build volume...

Caveat: I have printed this part but have not yet fired up my printer (still disassembled, as I am doing a LOT of mods at once). I see no reason why this bezel would not line up perfectly, but if it doesn't, please feel free to modify and remix. I...

The whole diorama and both models took 225hrs concept and modelling, 52hrs printing various failures mods etc . . all pieces have been tested and they print out very easy as long as you follow the settings. All of my models are only released when...

This mod will reduce your z-height by a little bit as the Motor Z kits have z rods included that are the stock length. So, in order to install the belt, you will lose some of the height... ~12-14mm. But, it will be worth at is your Dual Z will now...

You may also need to machine out some plastic from your outer barrel or do other mods in order to mount the new barrel. So far I have only tested mine in a Tiger 1, and I had to do some minor machining as the brass barrel diameter was larger than the...

Just believe me, I have printed a lot of mods and most of them are good looking but add almost nothing to the actual printer's characteristics. That is not true for the dampers! You will experience a shocking difference in quietness and a good...

You will need the parts that came with the MMU2S mod (IR sensor, the M2 Screw), you will not be using the magnets or the steel ball. You will need 2 extra M3x10 screws and 1 of the thin square nuts. The arm is removable and adjustable. ---- You...

VIDEOS A simple quick and dirty demonstration by me of how the knob works: https://www.youtube.com/watch?v=yPHjmhsJESk And a more professional video by Chuck Hellebuyck on how to install the knob (and some other useful CR-10 mini mods) on Filament...

BackgroundThis print file is an extensively modified remix of Arkon Lincoln SCX24 Beadlock Wide Rims on Thingiverse by CheapAZHobbiesI used PrusaSlicer to scale, remove material, & correct the geometry so it could be used on my SCX24...

Ender 3 XZ Housing + Endstop An adjustable Z limit Endstop is a really good mod for this printer. I guarantee it. # Update: Was going for a slightly different design at first, so the base and arm was chunkier at 10mm. Uploaded a slimmer arm version...

The 6 mini servo holes have a cable duct underneath and are general purpose except the two centre ones are reserved for steering and the option of a vertically trimmable steering nozzle mod. Plan is to fit the servos in with bluetack or power tack...

After making the SWISS background collection for modded gamecubes I was stuck wanting to modify the jewels, I found the prices a little bit privative for me so after some small trials I have come up with this!!Personally it cost me like less than 2...

To execute this mod, I employed an ATX power supply with a Molex extension cable and basic connectors. Everything was sourced from Amazon and is linked below. Keep in mind that you may need to modify the provided model slightly to ensure it fits...

To make it even more user-friendly, I added some mods that I'll explain below: Horizontal Arm: Added alignment marks around the pivot point at 30-degree intervals Created a cavity in the bolt area to accept a nut for a 1/4" dia. x 20 bolt Made a hole...

I am posting the SketchUp .skp file so you can make adjustments or mods if you need to. If not, use the .stl directly. Take notice: this file is on a 100:1 scale! I printed the parts using PLA 0.4 nozzle, with 50% infill. I used support,...

... * M4 different lengths: various * M3 different lengths: various 33. PLA Filament 1 kg: 1 Edit (20-04-2018): A new file, Frame_Hot_Bed_mod.stl, has been added to the BOM. ...This design showcases an optimized aluminum sheet that holds the hot bed.

Hot Bed Cable management. I actually started way back when with a Thing that fit over the exposed edge of the back left corner of the frame to prevent the cable from catching when the bed moved, but the cable still just flopped around, and I didn't...

also, I modded the front so that the lens doesn't stick out past the front of the print as it does with their stock design, so your ND filter doesn't rub on the lens. Also made a lip where you should be able to stick one of those small ND filters. ...