soviet tank object 279 3d models

In both models the part that attaches to the Fischertechnik parts is fairly quick to print by itself, so you can try a few different scales to see what works for your printer.Juh created his own remixes of these parts, and they are really...

That said, it's probably best to stick with whatever material the mould is printed with so that both objects end up with similar amounts of shrinkage. For the wheel spacers The diameter of the axel hole is 1.65mm, the outer diameter of the spacer is...

Once it is printed remove the supports and test fit them together, glue is not necessary on the joint but better to be safe than sorry *Note it seems that using Cura it is difficult to split apart, when uploading to Prusaslicer it can be split to...

Time for a bit of background : This build, and all of my related trefoil knot builds, were inspired by this video by “Big Clive” :https://www.youtube.com/watch?v=35xmE8Nurj8The object in that video was actually flat, and the 3D effect was illusional...

the object here is to reduce the layer lines and heavy marks to prepare to fill the imperfections.You will see how good your layer alignment really is in this stepDisassemble and Fill all the surfaces with glazing puttyDisassemble the top and bottom...

When you need to disassemble a track, remove the tressel arm, insert a small jewelers screw driver (or similar small object) into this hole, and press upward to separate the track segments. Following this procedure avoids having to pull the track...

Summary:The objective of the project was to create a ghost figure that could be printed by a 3D printer and used as a paperclip, keychain, or small toy that could be used for multiple different functions. With the use of a 3D printer it is...

It functions as a paperclip, a bookmark, a toy, an action figure, fidget, a stencil, a pattern, a key, an in class distraction, a comb, a back scratcher, a ear scratcher, a measuring device, a weapon, a lock, a massager, a sharp object, a utensil, a...

All of these objects i printed with 5 bottom layers at 16 seconds with 8.5mm lift distance, and the normal layers were printed at 1.4 second exposure (My UV power is at 75%) with 6mm lift distance. I set the Left speed to 110 and retract to 160. ...

(Credit; Chicago Architecture)   This object is part of "Scan The World". Scan the World is a non-profit initiative introduced by MyMiniFactory, through which we are creating a digital archive of fully 3D printable sculptures, artworks and landmarks...

Be aware, that when finally screwing the lamp foot together, simultaneously counteract the twisting of the electric cable inside (un-twist the cable through the exit hole in the lamp foot) How the lamp shade modifiers are set up As an example, this...

However, a system that allows for aperture adjustment, unimpeded use of the night vision, and complete light and foreign object ingress protection does not exist. Additionally other devices are complex and expensive while this device is designed to...

Currently a headlight module is available to build so you can unload an ungodly amount of light to see even in pitch black. https://www.myminifactory.com/object/3d-print-173156   This also requires you to tap into the battery wiring to read the...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

This is ideal for paint spray booths in wall mount applications to ensure effective and even lighting on all sides of the objects to be painted.Suspension Mounting: Pendant mount fixtures hang from the ceiling and are suspended by rigid pipe. Each...

Status after v4.1 I have reprinted most of the parts, not including the cab, I am using the original ossum cab printed at 80% height (found here https://www.myminifactory.com/object/3d-print-35986 with some body clips I printed and keep cutting down...

[60] instanceof исполнительascript должностьїж assistant A customized version of the object is available at http://www.thingiverse.com/thing:58001, made with the Customizer tool located at...

__If you would like a way to store your Hero Me Mutant assemblies and other Mutant devices while not on a printer check out my Mutant Workstation mounts here: https://www.myminifactory.com/object/3d-print-mutant-workstation-mounts-149200 __ Chris...

The Servo moves a mechanism inside to raise the eye brows and lower the jaw.BILL OF MATERIALSPartDescriptionQtyCostRaspberry Pi PicoThe $4 microcontroller from Raspberry Pi1£4.00ServoA low cost SG90 Servo1£3.00Ultrasonic Range FinderHC-SR04 3.3v...

You can remove objects called “brace front lower” and “brace rear lower” from the main print job if you want to use these.Drill Attachment - You can remove object called “gear 8” from the main print job if you want to use the optional...

Most slicers should have no trouble letting you split a multi-object STL into its constituent objects. But if you have any doubts about doing that, go ahead and download the individual models separately. One-piece print. This version combines the...

This encompasses the entire solid top of the mount, and in particular ensures that the blue bridging (shown below) that closes the top of the tube is printed at 0.2mm instead of 0.1mm (the 0.2mm bridges are more robust and fail less often):The...

These modifier objects will have to be added to the solid box parts in your slicer to get the desired result. I tested quite a while to find the most suitable infill pattern and parameters for it. A 26% filled gyroid pattern showed the best result to...

Many have reported, that PETG works too!Further Information and Tips:It took me around 4 weeks to design this Revolver from scratch until the object was printed and worked as intended. I googled the dimensions of a 44.Magnum cartridge and built...

This encompasses the entire solid top of the mount, and in particular ensures that the blue bridging (shown below) that closes the top of the tube is printed at 0.2mm instead of 0.1mm (the 0.2mm bridges are more robust and fail less often):The...

(See instructions and photos for details)A 0.7mm spill square is included to print first if you choose manual switching.High-Level Assembly Instructions (see further below for specific details)Printing:Print all the pieces.Inspect the hollow channels...

* `film-slitter-blade-holder-dual.stl` and `film-slitter-blade-holder-single.stl` -- These objects hold two or one single-edge razor blades, respectively. Use the single-blade design to cut your film into one 46mm and one 16mm strip, and the...

You also print these files from:MyMiniFactory: https://www.myminifactory.com/object/3d-print-9071...Thingiverse: https://www.thingiverse.com/thing:3501200Backside(1*)Batteriecover(1*)Frontcover(1*) Solder the Arduino to the PCB Solder the...

In some cases, that might mean your face is pretty much not a face but a hole with a rocket in it. High speed rocket to someone else's face. Some random woman in a Chelsea tractor driving over your expensive rocket and camera that landed on...

with a 0,50 width, set to 3 to have a 1,5 mm perimeters shells * First Layer Height: set to a value greater than 100% to have a first layer taller than Primary Layer Height and viceversa * First Layer Width: set to a value greater than 100% to have a...