wanhao duplicator 4s z axis brace and bushing 3d models

This brace I created for the wanhao duplicator 4s will greatly improve your prints by eliminating z-axis swing.. first two pics of other things is showing the weird swirls and rounded waves before I installed the brace. the last pic shows how...

I built a bracing system specifically designed to enhance prints produced by the Wanhao Duplicator 4S, effectively minimizing z-axis oscillations and distortions. Initial print attempts were marred by the appearance of strange swirls and rounded...

This custom-made bracket I designed specifically for the Wanhao Duplicator 4S will significantly enhance your prints by eliminating Z-axis oscillations. The first two images depict prints with unusual swirls and rounded waves before installing the...

There are numerous Z-axis support designs available on Thingiverse for the Wanhao i3/Monoprice Maker Select, but I highly prefer those mounted at the back. Designs like https://www.thingiverse.com/thing:2391089 and...

I've seen a lot of the metal rod Z-braces, and wanted to design something to give my Wanhao Duplicator i3 a little bit different look from the rest, so I designed what I will be calling "The Roll Cage". When it's fully assembled and attached to the...

I found only one z-axis brace for the Wanhao Duplicator 4, however it was only for the 4S.This is partially a remix of Delukart's Z-axiz-brace. Credit where credit is due, go there if you want a brace for the 4S.I adjusted the bushing to fit my...

This adapter fits perfectly in the Duplicator 4s and offers an extra layer of security to your bearing by adding a mounting plate. Ensure you have on hand a single bearing, measuring precisely 5 x 11 x 4 millimeters. Print Instructions For best...

I came across a DIY Z-Preloader designed for the CTC Bizer, so I decided to give it a try with my Duplicator 4s. Unfortunately, it didn't fit properly. Since there was noticeable movement in the Z-Axis, I took matters into my own hands and created...

A remix of Azza's "Z braces for Wanhao Duplicator i3, Cocoon Create, Maker Select, and Malyan M150 i3 3D printers."http://www.thingiverse.com/thing:921948 Just print the top_left, top_right and 6 of the balls from Azza's braces along with the 4 STL's...

Simply adjust the Z height in your slicer to your desired specifications and position the spacer around the base of your Z screw pillar. This particular spacer is 3mm deep, effectively halting your Z-home at 3mm below its normal operating level when...

Bracing is a breeze with the Z-axis of the Wanhao D9, all thanks to M10 threaded rods. I've seen other braces around, but they're made for imperial rods! Unfortunately, those aren't readily available in the UK, and besides, they didn't seem sturdy...

Streben um den Drucker einfach in der Z achse zu stabilisieren,Für die linke Seite einfach im Slicer spiegeln.Es werden noch benötigt:2x M8 Gewindestangen 405mm lang8x M8 Muttern und U-Scheiben10x M3 Schrauben 35mm langSimply brace for printer to...

Replacement front corners for the Duplicator I3 Plus enable the secure attachment of a camera on either the left or right side, providing a robust and versatile setup.

... the lever fails to switch correctly, as can be seen in the attached photos. This object was printed using Formfutura Carbonfill filament. Print Details: - Printer: Wanhao Duplicator i3 - Rafts: None - Supports: None - Resolution: 0.2mm

If they were along the X-Axis and the Z-Axis is askew, one may end up taller than the other, and you'd still have an alignment problem when using them to help align the Z-Axis. ...If they are in line with the Y-Axis, the worst that would happen is one...

The print in question was done on Formfutura's Carbonfill filament using the following settings: Printer: Wanhao Duplicator i3 Rafts: No rafts were used during printing. Supports: No supports were generated. ...Resolution: The print resolution was set...

Take one of the spacers and put it on one of the screws, then screw the z-axis stop to the bracket. Use a screw from another project to screw in the other side of the z-axis stop to the bracket. Then take the other spacer and put it on the other...

Begin by placing one of the spacers on a screw and then attach the z-axis stop bracket to the PrintInZ bed using that screw. Use an additional screw, preferably from another project, to secure the other side of the z-axis stop to the bracket. Next,...

*Updated 2017/08/22 with thicker walls and smaller inside hole to provide better seating for the damper and extra strength* This is a spacer to allow the installation of a stepper damper on the Z-axis of the Wanhao Duplicator 6 / Monoprice Maker...

Print Settings Printer: Wanhao Duplicator i3 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 100 Microns Infill: 30% Notes: Printed slowly because the parts are small. The frame mount part's orientation isn't quite right. Print it as you...

Here's what you'll need to print: * 3 M3x12 Screws * 1 M3 nut * An attachment point for your Logitech C270 Camera (others might not need it) One thing I got wrong: if you have a front Z axis brace, the arm will collide with the threaded rod during...

A second Z axis chain for the opposite side will also need to be printed, but this one can be enclosed as it is easy to remove the connector and feed the wire through. Then just thread your cable through the chain and wire things back the way they...

I've carefully crafted these templates to calibrate the Z-axis perfectly by relating its leveling directly to that of the Y-axis for maximum precision.

Strengthening the Hull of the Wanhao Duplicator i3 3D Printer. Every bolt hole is meticulously drilled with precision to match the specifications of the printer itself. In certain areas, additional bolt holes have been strategically drilled for...

I designed this system to streamline the process of calibrating the Z-axis. A makeshift spirit vial was crafted using an old, inexpensive torpedo level that I happened to have on hand - these components are likely universal and easy to obtain.

Here is the device used to adjust the z axis endstop. Its creator remains unknown, but users have successfully downloaded it from the wanhaoUSA website and installed it with ease. ...This adaptation serves as a convenient reference point for those...

... Printing Two Copies. A Note Before You Begin: If One Side Of Your Z-Axis Doesn't Budge At All, Even When You Twist The Other, Consider Jetguy's Fix On This YouTube Link https://www.youtube.com/watch?v=Oy8D6BZzKkU - It Solved My Problem Completely.

To rectify this issue, I created a new design for replacement parts and an alignment tool to measure and align the rods with the rear wall. The bottom replacement rods can be tricky to change due to their flat shape, but they are worth it in the...

I designed replacements for these parts and a "setting tool" for measuring and aligning the rods to the back wall. The bottom ones proved fiddly, but they're worth replacing. An added advantage is that after making the change, the bed leveled in...

This remix contains the following files from their respective things: [Z braces for Wanhao Duplicator i3, Cocoon Create, Maker Select, and Malyan M150 i3 3D printers.](https://www.thingiverse.com/thing:921948) * BallsMk2.stl * TopLeft_fixed.stl *...