OpenSCAD parametric fan model

 A side note - you also probably should be using my rear PC4m10 jack for your MMU3 https://www.printables.com/model/542409-mmu3-pc4m10-rear-connector The perfect length is one make an even curve downward and the up into the back of the MMU that is...

The first one was a box, with an RFID reader, that provided clues on its LCD screen and had a secret compartment that opened with a specific secret code. The second device was this Bocca della Verità with RFID in the mouth (it was a secret) provides...

This model includes both a solid and a honeycomb version whether you want to print a more authentic and traditional version of the warlock or if you want it to be more unique. I used absolutely bottom of the barrel parts to get this to a fully...

The design uses 12 '10mm x 3mm' (the magnets are actually closer to 9.95mm x 2.67mm).This is a spin-off from my earlier light-pull magnetic door catch: https://www.printables.com/model/209370-magnetic-low-profile-floating-head-quiet-door-catc , but...

As always, the .blend file and pre-supported .obj (the one that I used to print it on my Prusa mk3 with a .25 mm nozzle) for this model are available to my patrons at https://patreon.com/VirtuallyJason. If you appreciate my work and have a few...

The models in these STL files are scaled for a 58cm head circumference. (Refer to photo of T800 for how to measure the size you will need to print) Just scale in your slicer software on XY by 1/58*[your figure]. Do subscribe to my YouTube...

  I also modelled in clips for these PCBs to hold them in place whilst soldering up.I will share my order for my PCBs on jlcpcb so anyone can order once I figure out how :D Tools RequiredSharp knifeLong Nose Pliers Note that the 3mf...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

If you want to use the hardware I intended this to use:Hinges Bolts- https://www.mcmaster.com/91292A018/ (you will need to thread inner most hinge)Hinge spacer- https://www.mcmaster.com/91755A311/ (you can see in the photos a little bit of white in...

The assembly is not complicated, for each configuration I put exploded photos, pay attention to the insertion of the brass threads, (there are 2 models you need both), and to the direction of insertion, those placed in the attachment of the guides,...

I would also suggest allow for extra LEDs in your strips and to slide in your LED strips as you combine a segment to other segments. All in all, I learned a great deal about modeling using Fusion 360 and 3D printing using Slic3r and the Original...

However, they are split down the middle so they can fit through the holes with a firm hand, before springing back to the larger size. So thank you for the reviewer who made me take a closer look at at my model.I am always open to others ideas or...

Most parts do not need support and can be printed using the model orientation. BaseTopMotor and the Lid need “support on built plate only”. MotorMount needs to be rotated by 90 degree on the closed end (the one with the screw holes). In addition, it...

It's worth the trouble to get access to a laser cutter to get cut panels.  The duct is intended to print at a 45 degree angle - the part model is oriented as it is intended to be printed. The duct part DOES NOT NEED SUPPORT. Your slicer may...

Changelog: Update 2021-03-01: Steve (faultedlogic) made a remix for current A8 models with plastic bearing blocks. Update 4 (2018-06-17): added countersunk hole for chain fence Update 3 (2018-06-11): updated left motor mounts for different type of...

One important note is that I specifically modeled the pistol's grip to fit the exact CO2 bike pump specified. Theres no guarantee it will fit similar Bike pumps as I took measurements from the exact one I have. DISCLAIMER: By downloading these...

This version is included for those that want to create a custom playing field using other materials.Other Printing NotesWhile I was able to get pretty good results printing the sidewalls without supports, I did get better results adding a couple of...

If the diameter of mounting holes is (slightly) different you can simply scale the entire model (all parts) in your favorite slicing app to make it fit (the only thing that cannot easily be scaled is the small enclosure for the BT-amplifier). ...

 The switch is wired so it goes from Off to On with no sounds to On with sounds. ...

Able to hold 1 stack of cards and 2 columns of hexes. --4-2-17-- Added player card 2.2, a little bit smaller on the separator pieces that come off the model, should be easier to fit in the box. --4-2-17-- Removed older hex and cards .stls and...

If you have a printer, then you have such electronics! PaScn3D connection to Prusa 3D printer in a minute (tested!) – dedicated mounting brackets, components adapted to the dimensions of the device Modularity – adaptation to other printers without...

They aren't really required - they just provide some more protection. In addition to the printed parts, you will need the following: 1) 1/4-20 threaded rod, 3" length 2) 2 1/4-20 nuts 3) 2 M6-1.0 hex bolts 16mm length 4) 2 M6-1.0 hex bolts 30mm...

Please check the images to see what it is included in this kit.This set contains: - Dwarven Berserkers (6 + 6)- Behemot Riders (4 + 4 + 4)- Durnir – Berserker Lord- Tarum Bloodhammer- Thyra Blood Priestess of Duum (Dwarf Pinup)- Skutagaard War...

If the format you use is not yet in the downloads, let me know, I will create the models for it. Now print the test part (#0 testmodel) start with the smallest tollerance and try to push the test part over the profile, it should not go strongly...

The lamp stand, lamp shade and the bases of these two parts. The models in the STL files have the correct orientation. All parts are printed <strong>without support</strong> and with a layer height of <strong>0.2 mm.</strong><br/> Use an...

Team includes depreciated models such as the Medjay Pharaohguard Blitzer and the Iteru Deadshot Thrower. Not necessary for undead teams but enjoy! ...The Dynastic Destroyers are a proxy for Shambling Undead, Human, and Khemri Blood Bowl teams All...

...I propose some activities to do programming this robot: First goal: Making it move The first and basic activity could be to program and model their movement, to find the correct position sequence for each leg for a forward run. First step: assembly.

While jdrones refers to it as a 2830 motor (because they measure the bell) most other manufacturers/retailers classify this as a 2212 motor (based on the size of the stator) There is a model of the motor included in the Onshape document so you can...

Links to materials: Bottle with dispenser Tweezers set Spatels om het model van de tafel te verwijderen Tang Links to used tools: Tools for machining inner holes Scalpel with flat blade Large clamp Chopper-drill Countersink Silicone...

We are presenting a new wind turbine device, that is easy to 3d print, it can be made handcraft once it is viewed it components and how they get assembled in a very easy and intuitive view, This system have several pending patents and the device...