anycube photon mono x 3d models

### Introduction This is an **add-on** for [maggie-shah's](https://www.thingiverse.com/maggie_shah/designs) laser engraver that converts it to an unlimited x or y-axis engraver (depending on your configuration). The original design with the moving...

... For example, if I have 2 amps that are 2U's each, and 6 components that are 1U each for a total of 10 U’s, I would calculate the interior height as follows: 10 U’s x 1.75” per U = 17.5” 17.5” + 0.625” = 18.125” Minimum Interior Height of Enclosure.

Some additional tips/references, Tractor Supply sells 1/2" x 36" steel rod in the welding aisle, I would recommend using that and cutting down the rod to pieces as needed. Unlike NTBayerische not everyone works in a commercial machine shop...

----------------------------- If you encountered issues with the cold shoe, take a look at the remix made by [madebymonkeys](https://www.thingiverse.com/madebymonkeys) -> [LED Lamp Mount for Loc-Line 3/4 inch x 3 inch Ball...

The workmanship as a whole is clearly less skillful than that of the north frieze, although some of the scenes may be numbered among the masterpieces of the Parthenon (blocks III, X, XI, XXVI, XXXI and XLIV). The procession begins at the west corner...

My projects are still in growing thanks to you!My other LEGO related projectsCollection of over 20 display stands projects 🔗 - click hereFor LEGO Speed ChampionsFor LEGO Technic For LEGO MinifiguresFor LEGO Star WarsFor LEGO NinjagoFor LEGO Dune...

The torque is suitable for driving a RepRap printer's X or Y stages but the coils were found to easily overheat. I recommend attaching a heat sink to the exposed ends of the four electromagnets. IDEAS FOR IMPROVEMENT: Use steel nuts for iron pole...

i may add a second hole for wiring so it doesn't have to be drilled by others but right now thats how i got the led to the inside under the boot an up through the hole i drilled, put the body on first b4 trying to run the wires or they will try to...

Three Directional Scalability Since the Kinetic Hand uses flexible hinges rather than snap pins, it can be scaled in X, Y and Z directions independantly without compromising part fitment or function. Eased Fitting Tolerances Regardless of hand...

Suggest to rotate fan so that the cable is closest to the oval shaped hole.Then place the fan bracket onto the fan the base that clips into the AOOSTAR R1/R7 should be pointing upwards.Insert (4) screws into bottom bracket in a Z or X pattern and...

Hot End: Micro Swiss Firmware: Marlin 1.1.19 Stepper Isolators: Isolators Installed For X And Y Steppers Only. Preflight Checks Clean Clean The Print Surface Thoroughly A Glass Bed Will Give Your First Layer A Mirror-Like Finish. The Bad News Is...

At an impressive 12344 x 3246 resolution, this massive and finely detailed HDRI-sphere renders allow the sky to be rendered directly from the viewport, capturing every nuance of light with remarkable precision. This has been extensively tested for...

pinNrX = precision located with accurate results confirmed to ensure optimal X-Axis placement for enhanced productivity purposes pulleyH = precise dimensions checked off for correct measurements at the maximum possible rate without causing potential...

If you need any part to be reversed, like for ex ample you want Gun Turret to be on the left side you must mirror it on the X axis. ... Credits: This project was made on basis of: ...

Horizontal (or east-west or side to-side) axis measurement placed along same flat coordinate grid so items don't touch other parts as seen within actual, finished, complete print of any one model produced following this document's design...

I used mg90 for steering and the sg90 with plastic for the steering wheel.Servo cable splitter: You can solder the wires or use a splitter cable that costs around a dollar.Magnets: 12 neodymium magnets 8mm diameter x 3 mm thickLead for weight: I got...

The probe location remains in the stock X-Y position. The original Extruder LED has been added. Included pictures of a 0%-100% fan tower (designed by @OurAngryBadger) for comparison between V2 (in black) and V3 (in dual color).V3.0 Update 14.12.2023:...

Each part was painted individually before assembly) The completed model is 295mm tall after assembly. There are 40 parts, however the model is simple to print and build. Enjoy! Print instructionsPrint Settings Printer: FlashForge Creator X Rafts:...

I printed this design on a 310mm x 310mm Ultrabase glass bed, which provides a good balance of size and adjustability. If you need to increase the scale, there's room for slight adjustments. To print this design, I used the following settings: 25%...

The model's detailed texture map is available in stunning 4K resolution, ensuring unparalleled image clarity (4096 x 4096 diffuse). Built as a polygonal mesh for ultimate flexibility and detail accuracy. Every part of this model has been carefully...

Finger changes reduced z axis 10% and increase x,y 20%. Did a few adjustment on each piece to allow more freedom. (the following changes should allow better movement of fingers and get closer to a closed fist with hand.) This changes was tested on my...

Two Piece Parts Two piece parts have to be cloned and mirrored along the X and Y axis to be properly used. In Cura, this can be accomplished by selecting the model, duplicating it, and then choosing mirror and selecting the red and green arrows. ...

Optionally, of course, you could also pick up a Dark-Platypus Studio MAGNA-MAP, a high-quality rollable, laminated, 24” x 36” battle map that is made of magnetically receptive material! (now available at www.dark-platypus.com). Dark-Platypus Studio...

I believe I may have the older version, & that they've been replaced by the round style (see further down). I can't seem to find the flat style on the Topeak website (21 Feb 17) at all. Source style. Assembly & Instructions...

Anisotropy The first thing that comes to mind when I think of the final shape idea is how I will print it in order to have optimized orientation on the X/Y printer axes. Always thinking about anisotropic effects like someone working with wood needs...

The blank mount area uses holes that are spaced 41.753mm X 77.286mm, and require holes that measure 5.2mm to utilize the standard M5 computer fan mount screws. After everything I learned from this project, I would've just stayed with a Duet 2, but I...

Also, that way the connections wouldn't be available to make any shorts or be unintentionally damaged. The holes could be a bit smaller :) Final desing: top and bottom look the same (connections are hidden inside the plastic part) Making the STL...

If you are looking for more, check out our premium projects: https://codeandmake.com/premium Customizer Options We recommend you use OpenSCAD to customize this design. This design has the following Customizer options: Drive Drive_Type - The type of...

Print Settings Printer: FlashForge Creator X Rafts: No Supports: No Resolution: .2mm Infill: 10% For helpful printing and assembly instructions, refer to the notes below. Building the Model Colors (there are no multiple printed pieces) Yellow:...

Pole mount &amp; electronics enclosure for a 150mm x 130mm solar panel. This accommodates a 1.2" (30mm) O.D. electrical conduit pole.</p> <h3>Print instructions</h3><p><strong>Why I Built It</strong><br/> I have an outdoor weather station that has...