blink sinc module 3d models

Since the 3mm led are quite bright I use for a red led pair (at the stelas) a resistor of 560 Ohm and for a green pair 470 Ohm (at the dead head signboard). The resistors are located on the back side underneath the signboard in extra recesses. You...

Since I print mostly ABS and occasionally PETG on my Davinci Pro I was not concerned with a layer fan so I did not incorporate one into my design. Kind of selfish, sorry.  I have an delta printer that I use for PLA. Since it is an open design...

It's not something that I think is super necessary for a cane holder since it seems stable enough at this point. However, my initial adaptations of this design for the hiking sticks is not very stable (it's much easier to bump into those / knock it...

I even tried a couple of handheld Bluetooth keyboards, but since they were intended for typing, the designers assumed two hands would always be available for the task. Have you ever tried running while carrying a pie? Well, the same thing happens...

>(Just one coat was satisfactory for me since I was worried that two coats would alter sound quality and/or air flow.) > >(After 24 hours, the cage will be dry and complete. Hopefully your other components have printed, too.) 9. To assemble,...

Benoit took a different approach since I ask him to assembly the model without any instructions from me and give his feedback:- He glued the full body together with the strap_bottom and strap_top (using rubber bands to hold it in while the glue set)....

the waterproof one is designed to use stainless steel plastic screws You will need 1 RCA to 2 wire vga balun (well technically 2, since you'll want one on the other end as well) You can optionally just fill that hole in instead if you don't wish to...

Please feel free to make any changes you want since this is what owning a 3D printer is all about! Final Comments I will say this again: This is designed to reduce the smell of plastic from a print enclosure, AND NOTHING ELSE. While there are added...

Since this maybe desirable for someone who wants to make the doors moving, I'm also keeping the old version. Update 3: After printing the rear part of the engine hood, I added some tiny fillings for the door handles. The print turned out fairly...

Since the connector is attached by four legs (two on each side of the board and all four were soldered on my board) plus the center pin, this is not easy and I found it easier and safer to cut the mounting legs, remove the connector, clean off the...

When setting up my prints I prefer to be conservative, especially since the base of many parts are hidden when inserted into another part. For the smaller parts, a good first layer is helpful. *I used brims on: windshield front_hub_bolts...

Upload of my project from thingiverse since thingiverse has become trash! Unfortunately I can't upload .exe files here so you'll need to download it from the thingiverse page or directly through this line IntroductionProject GoalsI decided...

It does not have any sharp edges, so the risk to scratch furniture is minimal.Update 23.01.2021: Version 2.0 of this vice is now available here:https://www.prusaprinters.org/prints/53471Since it is much easier to assemble, without the need for thread...

No supports.Tensioner adapterSince the linear rails are readily available in lengths of 300 and 350 mm, but 300mm is too short and 350 is too long; this adapter allows you to mount 350 mm rail without cutting the rail. This part will also double as...

I also gave it a light coat of black paint, not enough to cover the 3D printing lines since I kinda enjoy them, and I feel they help tell the story.The legs were attached to the 3D printed part with double-ended M8 dowel screws threaded directly into...

 I don't suspect it's that big of a deal though, unless using PLA, since that stuff will definitely become too brittle to use as a hinge.   It can help when installing the filament hinge pins to cut the filament end at an angle, which may make it...

So I´ve got this stupid idea for a smaller RC-Benchy for a while. And I figured since it is such a small and simple project I just had to get it done, and in time for 2019 3D Meetup here in Sweden. So here it is, the Mini RC-Benchy, perfect for the...

\o/Since everyone's situation will be different and there does not seem to be a standard when it comes to the diameter of down-spouts, I'm not supplying STL files but the Fusion 360 Project file. Using this, you can adjust every relevant parameter to...

Make sure to remove the added supports on the face & bow-tie since they are not needed. I also set the support style to “Snug” which gives a minimal but very secure base.  Removing supports in the hollow interiorSince this has a...

...  My hotends have been in service since March 2021 with the old adapters and I've changed nozzles a handful of times since then so their MTBF has been okay for me but it you do a lot of nozzle swaps, it won't hurt to have an extra, ready to go.

Some consider this Z axis leveling, but are you really leveling the Z axis, not really since you are leveling the plane on which the X axis travels. This is to be used separately or in conjunction with Makeitmakeitmakeit's...

These are the same size that are used for Gridfinity baseplates and modules.BasesYou can use any of the bases with any of the connectors and any of the grip or support ends.Gridfinity Module as a Tentacle BaseYou can use the Gridfinity tentacle base...

Printing recommendations The stackable box can be printed with virtually any non-flexible material that you want, since the only mechanical effort that will be made is the support of one over the other, and for this it has been taken into account to...

Ever since I printed my first #3DBenchy designed by Daniel Norée arround, I've had the idea of making an R/C version of it.But I never got inspiration enough to actually do it, until I saw THENOMADSOUL_ (aka KimDIY) post a cool simple but functional...

- phase2-bridge-module.stl -- Standalone bridge module. - phase2-mastercom-nacelle-center.stl -- Mastercom style center nacelle. - phase2-mastercom-nacelle-port.stl -- Mastercom style port nacelle. - phase2-mastercom-nacelle-starboard.stl --...

Tactile switches are placed under the bar to detect when it is pressed. Bar Switch Subparts 3D printed snooze bar EVQ-Q2S03W tactile switches NeoPixel RGBW Stick Two NeoPixel RGBW LED sticks have been included in the front of the...

https://www.youtube.com/watch?v=hknXNxCtM_E It has lots of features, those include: Clock Mode Date Mode Temperature Mode Humidity Mode Various Lightshow Modes (like Snake and Matrix displays) Various Music Visualizer Modes A Scoreboard A Count-down...

Main electronics module Combines Uno / Ethernet / breadboard in a compact stack, that can sit under the printer. The breadboard contains the circuitry to multiplex the serial control signals that collect data from the magnetometers. It also contains...

Depenending on the changes made to the ROV to accomodate your equipment, you should spend a module performing rough bouyancy calculations and structural diagrams to get an idea where you will be at. Will you be running batteries, or using shore...

| | kiev-weapons-module.stl | Weapons pod. | | lenthal-nacelle-port.stl | Port warp nacelle. | | lenthal-nacelle-starboard.stl |...