curtain glider hooks 3d models

Instructions Followed 3Derp's photo gallery for most of these -- here are my suggestions (I plan to upload a start-to-finish guide to building one of these including the retropie setup if 3Derp is ok with it, but for now some quick tips): Configure...

I also made it optional to hook up a microswitch control panel using one of the analog pins (see infos in the Arduino code).While I plan to add a bit more documentation in the future I don't think I will evolve the design much further, it is very...

Add a bolt and a nut to the small hole in the wall in Base, and add a rubber band or spring between that bolt and the hook in Cam Arm. Add some grease. This Cam Arm should now add spring tension to your roll axis. Your joystick shaft should now move...

After everything was hooked up, the lid could be bolted onto the case. When the wheel reached maximum speed, holding the box with the on/off switch facing upwards and turning it clockwise or counterclockwise caused the wheel to level out. Remember...

Do not use PLA or any carbon/glass filled filaments as the hooks will snap off.Tolerances are tight, make sure your printer and filament are well calibrated! If anything doesn't quiet fit then sand it down.Main Body3 walls/perimeter15-20% infill...

Bend the tips of the leads and hook them through the notches on the CREE LED, soldering them to the LED. **Step 8: Attach Copper Heat Sink** Using provided adhesive patches, attach the copper heat sink as square and center as possible on the back of...

You will also need a rubber band (I used a #33) that fits over the little hooks on the handle side and stretches over the groove in the other side to pull the sides together. (See 6th photo) A little light grease on the rails will help the parts...

guide the cables from the rgb trough the little hook and trough the BL-touch cable guide. 5)to mount the hot end, you have to remove the heatsink etc first, because the hotend uses a screw behind it. you have to put the heatblock cables trough...

Clip version will be added in future.) Platsa_Mini_Sheet_Mount_V2 (Screw on dual Sheet holder for Textured&Pei Sheet on the right side) Platsa_Mini_SH_Mount_V2 (Spool holder holder :D Simple hook to mount the spool holder which came with the Mini, so...

https://www.amazon.com/dp/B00S5WPSZ2/ref=cm_sw_su_dp For assembly I suggest putting your stack all together - getting all the cables hooked up, fan sitting on top of the heatsink, drive(s) attached to brackets, board sitting on drive brackets. ...

###Compact, All-In-One Design: - Element reel doubles as antenna insulator - Guy lines are stored on the center hub that nests in the element reel - Stakes do triple duty as stakes, a handle for the reels, and clips to hold the reels together for...

For the assembly of the box, here are the necessary elements: - A wall plug - 4 small wood screws to fix the frame - a metal hook or a screw to hang the frame on the wall - Plants, I took plants that require little maintenance. Hanging plants are...

Using the Customizer, create a customized version of this thing: http://www.thingiverse.com/thing:58001 The specifications for this customization include: - Pattern Overlap: 18 - Pattern Shape: 5 - Input:...

I recommend to hook up the strips first and the ring in the end. I've soldered some led headers to the ring and criped a connector to be able to quickly remove the ring from the system. Yes, I've messed up the wire colors... Assembling the frame...

At the far end, I will attach a miniature USB camera that can connect via cable to the phone mounted on the 8mm tube (hence the small hook on the cam housing). This way, I'll be able to inspect hard-to-reach places, such as under a car, boat or in...

push 1/4 hoses in (I used 1/4" hosing from Lowes, its $0.16 per foot), push hard, you may have to use a 7/32" drill bit (you want a snug fit, otherwise you will have to use sealant on the hoses) hook up a pump (I use a small pump, I got it on ebay...

The walls of The Salvager's Ramparts are rigged with gears, which can supposedly be triggered by a switch to allow larger vehicles to enter - providing a thrilling adventure hook for your games. Access points are conveniently located via stairwells...

To attach the rear winglets you should hook one side on the rear engine mount and then squeeze the ring gently, pushing it on the other mount. Once attached it will rotate (as seen in the pictures attached) and friction will keep it from moving. The...

Once the turntable is in position I'd recommend hooking it up to a PC with the Arduino IDE installed. This is so we can test it and work some grease into the gears. Temporarily reattach the turntable to the PCB, connect the scanner to your PC and...

To guarantee safe pulling out, the OdAZ-885 has a conveniently placed fork at the back featuring an extendable finger and ample space on the rear cross-member for installing a reliable tow hook. This impressive semi-trailer comes equipped with a...

It's now high time to hook everything up and test this beautiful piece of work! Unpack your newly obtained DC-DC converter and prepare to make some electrical magic. Connect the wires going out of the case using some well-positioned jumpers for...

The holders are free standing and peg board compatible (3" spacing on the peg board hooks). There are four object files because there are four variations of essentially the same holder: "Original": the original design with more embellishments, and...

Please note that this model doesn't include the hooks on the bottom for the external antenna coupling. My car doesn't have one but I think it can be added easily. You can find the assembly instructions in the print instructions or here at...

It's good practice to hook the front on first and then lock in the back tab. Reverse when removing it.</li><li>Slide the pivot down on the stick. The ball joint should be in the center. Align the bottom edge of the pivot so it's parallel with the...

The full set of stereo components: https://www.thingiverse.com/guppyk/collections/my-stuff Bluetooth 2.1 Amplifier Enclosure I recently posted an enclosure for my favorite Bluetooth stereo (not 2.1) amplifier board, which I am using with my JVC Zero...

Things you'll need: a 3D printer with a print bed around 300x300mm 7 1kg Spools of Grey PLA (might only need 6 spools I had a few failed prints & design changes) 1 1kg Spool of Translucent Red PLA 1 1kg Spool of Clear PLA (optional if you want to...

This thing is pretty heavy and the magnets alone won't do the trick, so I also made a hook to hang the body from a ceiling. <b>Assembly infograph included!</b> Use the official renders for additional references. The face shield and flaps are...

H - With its characteristic hooked or bent shape, H is easily identifiable and reproducible, facilitating seamless communication among sign language users. I - The ninth letter, often distinguished by its elongated or stretched shape. This...

Once again be mindful of damage to the ring. Install the bearings for the design you used. Once the turntable is in position I'd recommend hooking it up to a PC with the Arduino IDE installed. This is so we can test it and work some grease into...

Hook it to one screw and just go around the frame, up and down as required, and you should eventually come back to your starting point. Tension it gently by hand instead of going at it hard - too much tension will warp the frame out of square. Leave...