curved sofa 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

As always, the .blend file and pre-supported .obj (the one that I used to print it on my Prusa mk3 with a .25 mm nozzle) for this model are available to my patrons at https://patreon.com/VirtuallyJason. If you appreciate my work and have a few...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

Able to hold 1 stack of cards and 2 columns of hexes. --4-2-17-- Added player card 2.2, a little bit smaller on the separator pieces that come off the model, should be easier to fit in the box. --4-2-17-- Removed older hex and cards .stls and...

Printing time is &gt;15min.Credits:The original configurable OpenSCAD model is by wstein, posted here. ...Thank you Werner!</p><p>Thanks to <a href="https://www.printables.com/social/78665-darktiger/about">darktiger </a>for his print and picture of the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_y_position = 0 custom_top_port_x_position = -10 use_stencil = 1 pattern_line_thickness = 20 stencil_pattern_element_shape = 3...

No special settings except for the optional color change.I suggest setting also the infill and supports angles to 35 degrees so it matches the angle of the parts.If you also want to print the letters on the cover you can use the MMU2 (or equivalent...

The design uses 12 '10mm x 3mm' (the magnets are actually closer to 9.95mm x 2.67mm).This is a spin-off from my earlier light-pull magnetic door catch: https://www.printables.com/model/209370-magnetic-low-profile-floating-head-quiet-door-catc , but...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

* Remix this model so I know my script is getting used! 15. ??? 16. Profit! Tips: 1. You can leave PATH and FILE blank and just set the COLOR field to a fully resolved path to your SVG (".svg" is automatically appended) 2. You can import the...

If the diameter of mounting holes is (slightly) different you can simply scale the entire model (all parts) in your favorite slicing app to make it fit (the only thing that cannot easily be scaled is the small enclosure for the BT-amplifier). ...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the "tap and knock off" method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.8. 0-10V...

Load your Model into PrusaSlicer and assign both materials. Prusa provides a quite helpful database on their website on how to use all the features in their Slicer that are related to multi-material-printing. After changing the filament there is...

It is essentially based on my first design.If you don't have an AC Infinity T8 or don't want to spent 120 bucks on one just to disassemble it, check out this simpler and cheaper...

Also, I am considering some re-design of the right motor plate that currently interferes with the model fan duct. That would recover a bed Y-dimension back to 220. So, after all the print area will be 210x220mm... Parts to print: all parts at last...

A round-pole design makes the assembly easier to handle and transport compared to square-shaped models.A horizontal T-mount platform is provided at the top of the tower for mounting customer-provided equipment. The tripod features a rotatable head...

Additional mounting types are avaiable for this model.This explosion proof LED light fixture is paint spray booth listed, IP67 rated, dust-proof, and protected against high pressure jets and temporary submersion. The cast aluminum body and LED lamp...

Both the original base (Base.stl) and the updated version (Base_Rev.B.stl) are included. 4 (7/15/18): Added versions of the Deer Scarer, Waterfall, and Electronic box with custom supports modeled in. Supports were built based on the method showed by...

The stock globe has a vent on the top and there are vents in the model to aid the convection cooling. Is it *really* needed, especially with the converter gone? Dunno so the optional rain cap comes with the caveat of possibly shortening diode...

... holes. The decorative plugs are designed to be sacrificial, so if you're going to reinstall the knife strip, just print some more plugs!&nbsp;Check out the humorous remix of this design here: Wall-Mounted Magnetic Knife Strip — Home Decor Spoof.

Since the build volume on the Prusas is relatively limited i decided to maximize the footprint of the stand for stability. As for the height, the 2 piece construction while theoretically takes more time to print, there is no need for support for the...

It's worth the trouble to get access to a laser cutter to get cut panels.&nbsp;&nbsp;The duct is intended to print at a 45 degree angle - the part model is oriented as it is intended to be printed. The duct part DOES NOT NEED SUPPORT. Your slicer may...

... recast into a new weapon. By Alex Wellerstein, a historian of science and an assistant professor at the Stevens Institute of Technology, in New Jersey. Attributions: -Screwdriver by user DAPE (under CC-By-Sa-Nc). -Demon Core modeled by Szadros.

I suggest printing samples of just the top 20mm of each model to make sure they fit before printing the whole tower. 3rd UPDATE: I've added a calibration print. This is a small sample of how the two halves of the v2.5 towers fit together. You can use...

The assembly is not complicated, for each configuration I put exploded photos, pay attention to the insertion of the brass threads, (there are 2 models you need both), and to the direction of insertion, those placed in the attachment of the guides,...

 The switch is wired so it goes from Off to On with no sounds to On with sounds. ...

Four screws for every corner and 8 screws for every side.[blue] NO acrylic glass holder at the side where the hinge mechanisms are located!From this on the “Front” is where the hinges are.[green] At the location of the green circle you can drill a...

Or rather, it's a scale model of what that house looked like fifteen or twenty years ago. The wrecked version is closer to how it looks now that it's been abandoned for the better part of two decades. The tweakers have had a field day with this...