easythreed x1 firmware 3d models

10/22/2017 EDIT: I'm currently setting up my firmware and don't like how far my bed sensor is from the nozzle. I'll be fixing this soon. 10/31/2017 EDIT: I've recently switched to ABS for a production job, but I've had some issues with warping...

-Mount BLTouch if you haven't already -Wire everything back to the board -Flash your firmware. Make sure it has BLTouch support and setup. You don't want to crash your build plate. -Calibrate and enjoy *Update Notes 3/16/19: 1. Reworked main body...

I've updated Configuration.h in my Marlin firmware and now it boasts full 180x180 plate space. I also turned my head 180 degrees, and to my relief, it works perfectly fine. Remember, you should never over-tighten linear ball bearings if you want...

To set the new origin position, you have to homing the axes and measure the distance between the nozzle and the angle of the bed, then change the parameters in your firmware. In Marlin, you can set the position of the origin in Configuration.h (this...

He shot much better than I did :) Parts links below: TWO TREES TOTEM S 40W MKS TFT35 CNC display Corrugated Tube 7x5mm Corrugated Tube 10x8mm Laser Honeycomb Working Table 300mm*200mm Firmware for the display And some photos in addition: My new 3D...

I will only add on my own: do not write the firmware to an SD card from a Mac, something will go wrong :) ... Pictures will be torn ... Also added a seal that covers all the slots of the profile. Although my machine is equipped with a chip sucker,...

Use those measured values to adjust the steps/mm settings in your firmware. The formula is: new steps/mm = target size / measured size x old steps/mm. After a few iterations, you should have accurate calibration of the steps/mm in both axes. Next,...

If needed, I can upload the modified Marlin firmware for the Ramps 1.4 board with bed leveling support and RRD fan extender board support required for dual extruder setup. It's just not done yet because I'm still fine-tuning the bed leveling range...

The firmware from this project - https://www.thingiverse.com/thing:1009659 Parts list: 12x Quality Servos MG996R - http://ali.pub/49vqac 1x Arduino Nano - http://ali.pub/49vpsn 1x Expansion Board - http://ali.pub/49vpo6 1x Bluetooth module HC- 06 -...

Convince Ultimaker to remove or raise the temperature restriction in the firmware, as there is no PTFE bushing to be damaged (or wear out). Convince 3D Solex to package their print core without all the parts you don't need, and maybe a mounting...

I've also had a Hypercube build in the works for a while now, so I just raided what I needed from that.) I printed the plastic bits in eSun solid-purple PETG: https://amzn.to/2DR27Aw Some significant differences between the stock A8 (or AM8) and...

So go ahead and print the firmware appropriate for your printer.icarus-sherpa-mini-r1-xmax-firmware.gcodeJust place it on your USB stick and print like you would print a normal model. It will make adjustments to the motor directions, X and Y...

Control a computer via an Arduino: You can use a small firmware on an arduino along with a shell script to automate tasks on your computer. In the example code, the shell script uses xdotool to generate a Right arrow key press, which allows me to...

This is a Single Extruder Modification; it may or may not work with the factory firmware. It's working in My machine, which has a Duet2 board fitted. 18-10-2020: You may need to reduce the carriage scale by 1% if your carriage binds on the left...

If the screw goes in tight without incident you should be good to go. I also used these magnetic cables: https://www.amazon.com/gp/product/B0772QDGJ4/ref=oh_aui_detailpage_o08_s00?ie=UTF8&psc=1&tag=tv-auto-20 I have designed spacers for these...

-- Solution: Replaced guide rods, attempted to re-flatten the bed as accurately as possible, and modified firmware to Marlin 1.x and enabled bed leveling using BLTouch. (Still utilizing the Anet controller at this point) 2) Hot bed intermittent...

:)====================The WLED firmware can be downloaded from here: https://install.wled.me/3D printed parts, wiring diagrams, FAQ etc can be found here: https://diymachines.co.uk/====================SAY THANKS:Provide continual and dependable...

Behold the now second working solution to the Creality / MicroSwiss CR10S PRO V2 Super Stock OEM original fans and BLT mounting solution for the all metal hot-end that has the following features: works with stock OEM fans designed for MicroSwiss all...

Recommended build components: motors: 4x 1806 2280kv (or 1306 3100kv) ESCs: 4x ZTW Spider 18A (or similar size and amps) flight controller: CC3D Atom propeller: DAL 4045 BN (or similar) battery: 3S-4S LiPo 850-1300 mAh FPV camera: Sony PZ0420 video...

(Note: some have reported that it works out of the box with AstroPrint as well.) Features: Displays the print status from OctoPrint Server Estimated time remaining Time Printing Percentage complete Progress bar Bed and Tool Temperature Screen turns...

A 40mm fan should be used for this assembly, and adjustments can be made as needed through firmware. Please note that this project requires advanced building skills, and if you are unsure about any aspect of the design, feel free to ask for...

Firmware download (.hex for easy flashing): https://drive.google.com/file/d/1oHYlpksgzbGCRKHOrl9qC4OLmhx7LOPO/view?usp=sharing The unused area above the motors was previously untouched. Utilize this entire printability by raising Z motors and rods to...

Update: (9/21,2020) Updated design by moving the two screw pegs for the switch board back slightly, as their position was causing the switch to trip early, stopping the carriage a couple of millimeters short of where the original stopped it, which...

Sliding this in and out repeatedly (and wiping any cooled plastic off) will then allow you to establish the height difference between the nozzle tip and the z-probe tip, which you can then permanently set in the firmware. Don't bother with a "paper...

... PPM (for use with Immersion RC 4 Channel Lite, mounted under the Naze32) planning on moving to cleanflight firmware shortly. Taranas 9XD Settings. Adjustable Expo @ 0, 35%, 65%. ...I could shorten many of the cables, possibly saving another ~40g.

Be sure there is a RESET command in your keymap.c, to be sure to update again the firmware in the future without having to open the case. 9. Optional: fill the bottom of the case with silencing foam from Home Depot, to make the typing sound less...

This firmware is version 2.0.0.bugfix for gt2560 8-bit cards. It has been tested on gt2560 rev.a, but it should also work on other cards with minimal modifications. To change the length of the Bowden extruder tube, you need to modify the following...

... Finalize the assembly with the [Bear extruder and X axis guide 5 "Final adjustments and calibration"](https://guides.bear-lab.com/Guide/5.+Final+adjustments+and+calibration/14?lang=en) using the recommended firmware and settings from Bondtech. 5.

This allows a person to use their 3D printer as a laser cutter/engraver without firmware or hardware modification. Simply remove the filament from your extruder, turn down the heat and clip on the laser diode.</p><p>-----------------&gt;To create...

Buy me a cup of coffee Buy me a cup of coffee $3.00 USD Buy me a massive cup of coffee $5.00 USD Give me a caffeine coma $10.00 USD ------------------------------------------------------------- Update 4: Updated the SiCK-68 EasyAVR folder...