ender 3 pro y axis linear rail 3d models

This is a remix of the linear rail X-Axis conversion kit by SnakeP on thingiverse.It's different in 4 ways:a bit easier to install (comes in two parts - no worries, it's still incredibly strong)the top can hold any upgrade the user would like to...

Update: 29/06/21 New flashed version added for who has on backside DD stepper cooler or wide stepper that can hit the z axis extender.(beta042 new file) Names can be confusing I use onshape to design my needs and on onshape free account, every design...

Tinkered the Ender 3 Pro Y-rail mount to fit on a normal Ender 3 Y-rail. Then tinkered the 2020 ball-joint knob on it. Use it together with the rest of the Ender3 Flexi PiCam Mount by eatthistim (https://www.thingiverse.com/thing:4041117 ) to mount...

I intended to install my bracket onto the y-rail but discovered that the connector was slightly too short. ...I therefore decided to extend the shaft by approximately 20mm.

I didn't find a picam mount I liked so I designed one that fits snugly over the Ender 3 y-axis tensioner bolts without requiring disassembly. The field of view is most of the print bed until the y-axis is fully extended, and it clears the axis at...

cam-holder arm to be mounted on the y-axis of the good old Ender 3. Fits perfect to the Pi cam mount. ...It needs only one M3 bolt to connect to the cam case.Use the clips to hold the cam cable in place

This arm mounts on the Y axis of the ender 3. The slot on the mounting block is tight enough tolerance that it doesn't come anywhere near interfering with the belt. There's a 10mm hole in the top, where I hot glued an M6 screw to mount the...

Rail Seat & Cushion for Kywoo Tycoon Slim Y-axis Linear Rail Kit

I really liked this design, especially the belt tensioners. ...However the plate did not fit on my standard ender 3, so I redesigned the plate

Slightly longer, tighter, and and taller arms for a more firm grip on the Y-rail with less slop. ... The mount arm/hole is slightly larger/thicker too for better support of the camera with space for heat 14x14mm heat sinks.

Enables you to add a damper to the Ender 3 Y-axis on models featuring a press-fit pulley that's difficult to remove. The metal motor bracket should be relocated to the opposite side of the Y-axis bar along with the endstop switch. This new endstop...

Not so elegant, yet simple, working Y axis motor cooling duct for Ender 3 designed to fit a 50mm fan. The case that I'm using is on Thingiverse at https://www.thingiverse.com/thing:3820335. To mount it you will need: - 2x M3x18 screws to mount it...

... other parts from the original post. I took the original design and chopped off 7mm from the end to allow my ender 3 pro's bed to utilize the full 235mm on the axis. ...The original design caused the bed to hit the tensioner when fully extended.

I loved this mod Ender 3 v2 (and other) Raised Squash Ball Feet by Kamel Makhloufi | Download free STL model | Printables.com but found that at higher print speeds the Y axis wobbled a lot so made up this support bracket to use another mount to...

I was struggling with my Y-Axis stepper damper on the Ender 3. Found a solution: https://www.thingiverse.com/thing:3024360. It worked well but had some flexibility in the bracket. I simply added a 20 mm reinforcement to the side that secures the...

You'll need the following parts: One 5mm Bore (toothless or 20tooth) GT2 Idler Pulley Optional: M5, 5mm longer Y-axis stepper motor bracket-to-Y-beam screw. This will allow it to extend through the male bracket and keep it firmly in place. ...One of...

... onto the board for drilling holes accordingly. Mount bearing holders with M3 screws and nuts, then install the Y axis on rails at 15.2cm apart, ensuring smooth movement. ...Lastly, attach the timing belt, heated bed, etc., to complete the setup.

The installation process was relatively straightforward: I didn't use the gauge, instead placing the rails in position with one center bolt slightly tightened and one on each end, then carefully tightening the end bolts as I centered the rails on the...

Using the newest parts you will only need: x2 5mm Bore toothless GT2 Idler Pulley (one for each axis) This is the bracket I'm using to add an idler for the Y belt on the Ender 3. While the bracket is fully inserted into the aluminum extrusion, you...

This mount is intended to be used on an Ender 3 Pro Y-Axis. The mount has a 9mm offset so it can be used with larger motors, or stepper motor dampers. My machine is equipped with a 48mm stepper motor which necessitated this mount. This stepper...

A Gopro mount for the Ender 3 Y-axis . Includes 4 pieces: 1)The mount - requires 2x M5x16 0r M5x20 screws to fix. These just replace the existing screws holding the tensioning end cap. 2) A 50mm Gopro-compatible 90°extension. This requires...

[Ender 3 V2](https://amzn.to/2MddE5f) Y-Axis Stepper Motor Damper Mount remixed from the design by: [Ra1ns](https://www.thingiverse.com/thing:4591114) to fit my specific dampers and provide clearance for full retraction of the Y-axis. My dampers:...

If you're trying to add dampers to an Ender 3, your printer's carriage might crash into the stepper motor on the Y axis or you could end up with press-fit stepper gears. Either way, the solution lies in printing the adapter found here:...

I've tried some different direct printing tools on my Ender 3 v2 and all of them make me loose between 0.5-1cm on the Y axis. Yesterday i was talking about this to a frend who told me a way to enlarge that distance on the Y axis in a easy way. He...

I've tried some different direct printing tools on my Ender 3 v2 and all of them make me loose between 0.5-1cm on the Y axis. Yesterday i was talking about this to a frend who told me a way to enlarge that distance on the Y axis in a easy way. He...

Problem: Adding a damper to the Y axis stepper on a late model Ender 3 causes the bed mount to collide with the back of the motor due to increased width. A possible workaround is to move the Y axis end stop forward, as shown in [this...

This is a minor stylistic change to Jody_T's rail cover to match the rest of the [Better Ender 3] series of parts I've created or modified.

Tinkered a custom Y-rail mount to fit seamlessly onto my Ender 3's standard rail system. Next, I successfully modified the 2020 ball-joint knob to integrate perfectly with the new setup. I paired this innovative modification with eatthistim's...

Frustrated with regular clips slipping off the front rail, I sought a solution to stabilize the camera and ensure it remained level, assuming a well-calibrated machine is essential for accurate results. ... The original arms and mounts can be accessed...

I'm attempting to create a better Y-axis guide for my Creality Ender 3 printer. To achieve this, I've successfully converted from four bearings to three and made the clearance easily adjustable without needing an excenter adjustment. One possible...