heated build platform 3d models

I didn't want to solder the wires to my heated build platform. I was also afraid that using 3 pin and 2 pin headers would, they would come apart or get damaged while printing. It's also hard to grab those little suckers in the back of your bot. I...

This is a heated build platform I made at home with things I had laying around. It works. Instructions Get a dual-sided copper clad board and clean it with steel wool, and acetone (not at the same...

I got tired of having my clamps scrape the bottom of my heated bed, so I designed a build platform coupling. This coupling wraps around your heated bed and your glass (3mm thick) There are two full build plates one has supports in the rails for...

While I did the video with an object that had already been removed from the platform as long as the object is a decent height I have had no problems removing objects from the platform this way. This project will allow anyone without an ABP to...

This model was designed to support the cable of HBP (Heated Build Platform) heater. It is used in the Artifex 3D Printer (http://www.3dmakerworld.com/artifex), and can be used in many other 3D printers as well. Installation instruction is provided...

Instructions Support open source 3D printing research and development by buying it from MakerBot at http://store.makerbot.com/cupcake-cnc/makerbot-cupcake-heated-build-platform-v2-0.html Full instructions are on the MakerBot wiki:...

Instructions I) Prepare the Heated Build Platform 1) Print 3x the small corner pieces. 2) Print 1x the larger corner piece with molex connector holder. 3) Bolt two of the small corner pieces to the right edge of the standard Cupcake wooden build...

I really wanted a fully integrated solution for controlling a heated build platform, as well as for communicating with the motherboard. I also wanted to be able to use the heated build platform as a controlled hot plate in order to do surface mount...

A simple 6mm thick Heated Build Platform. This was designed to make my ToM more reliable. As I have been dialing in the Z height more accurately recently I have encountered issues due to slight warping of the HBP's PCB and have had a few occasions...

I really wanted a fully integrated solution for controlling a heated build platform, as well as for communicating with the motherboard. I also wanted to be able to use the heated build platform as a controlled hot plate in order to do surface mount...

I received, and built, the MakerGear ceramic heated build platform and am very happy with it, except for the aluminum plate that sits on top. I have it taped down but it was still sliding a little, not much. Didn\\'t want to attach it with...

Many, many owners find that the Heated Build Platform on their CTC Dual Printer (which is a clone of the Flashforge Creator, which is in itself a clone of the Makerbot Replicator Dual), is woefully badly calibrated. The HBP is based on the original...

This model was designed to secure the glass top and heat spreader to the build platform without binder clips. The corner can slide in and out to secure or release the glass top. The design is used in the Artifex 3D Printer...

and then quite un-literally, unfortunately) So I made my own HBP - but the insulation was uneven and resulted in a horribly crooked build platform with a nasty tendency to give more on one side than the other. Very much inspired by:...

Build to the max: Add inches to your build platform, and avoid hitting bolts by buying the parts to make the Thing-O-Matic's Heated Build Platform work in your Cupcake CNC. ... Instructions I've been...

Updated 2013-12-22 ctheroux has published an improved version of this part at http://www.thingiverse.com/thing:204666 This clip gives an anchor point to which the heated build platform power and sensor cables may be tied on a Prusa i3. The raised...

This is a casing that fits over the heated build platform plug. It holds the wires securely to prevent damage to the soldered connections. Instructions Additional Parts. 2 M3x12 bolts. 2 M3...

Amazed by the extra-rigid piece of aluminium and the extremely limited heated build platform 1.0 of my Cupcake, I decided to buy the Thing-o-matic HBP and then adapt it to my printer. All sorts of strange designs came to my mind, and finally I got...

... simply a one layer thick plastic for seperating objects from the plaftform. It might be not as efficient as metal tools, but you don't have to worry about damaging the platform. (ya ya, just another replaceable tool for 3D printer, I knew... ...)

Instead of using washers or spacers to hold up the springs on the replicator. I used printed spacers. ... Instructions Print and Replace!

I didn't like the drawing so I made my own. Here is mine (minus the title block, which has company information on it). Feel free to be loosey-goosey with the tolerances but that is what I am aiming for. ...

http://www.ebay.de/itm/IDE-System-HBP-heated-build-platform-for-Makerbot-Replicator-5th-Gen-/352004451045?ssPageName=STRK:MESE:IT or directly in our shop http://www.ide-3d.de...

http://www.ebay.de/itm/IDE-System-HBP-heated-build-platform-for-Makerbot-Replicator-5th-Gen-/352004451045?ssPageName=STRK:MESE:IT We also have an online shop where it is a bit less expensive cause of the ebay fees, but the international Version is...

A robust and sturdy 3D Printable Build Platform/Heated Bed Standoff for the He3D K280 Mega Delta and many other delta 3D printers built with 20mm slotted extrusions. The design replaces the adjustable spring standoff supplied with the K280 kit,...

The extra surface area of the build plate will take longer to heat up, so you should only do this modification if you want the extra room, or if most of your prints are multi-hour affairs. Here is the saga that led up to my larger HBP: My original...

Just my design of a heated build platform using calidum heater.

Mendel Acrylic Build Platform with holes for MakerBot Heated Build Platform

The sensor wire broke on my heated build platform so I designed this to prevent it from happening again. Instructions 1) Use cat6 cable to replace the original 2 cables -use 2 pairs for the power...

... The hole in the middle was added to provide a way to route the heated build platform wires and make for a cleaner end design. Instructions 1) Laser cut. 2) Build a printrbot.... ... ...3) profit?

This is an initial prototype that does not support a heated build platform. I intend to add HBP support at a later time. I'm also still playing with conveyor belt materials. I've started with some Duralar I picked up for an art supply store. It has...