untuckit models

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 42 custom_bottom_fillet_resolution = 8...

Any longer and you'll have to either modify the model or hold it steady by hand while screwing in the first few mms until the guide grooves engage. Any shorter and you'll lose variable length and have to use a tighter initial state for the...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

The sled is sized for my needs and my Harbor Freight table saw, but easily adapted to other makes/models. *I include the OpenScad file for easy customization*. The rails are 200mm long. I printed 4 total to achieve 400mm rails. I rotated the rails...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

... heliostat not being able to rotate 360 degrees (since that would tear the MLI).The rover design is merely a representation of a possible movable platform and the focus of the design lies in the heliostat itself. Rover wheel model is by Daniel Loera.

You just have to have the right case respectively.If you use the original MK3S+ frame check out the version for the original Prusa frame. FeaturesWorks with Raspberry Pi 3 and 4Works with any type of Armor-style case that uses M2.5 screws. Just...

This new model boasts significant durability enhancements, enabling it to withstand heavy grounding without sustaining terminal damage - a critical feature for FPV enthusiasts, especially during the learning phase. I won't claim that it matches the...

...All "mandatory" supports are already in the model. This piece on the photos was accidentally done with 0.15mm layer height and it turned out fine, although I intended to print it with 0.08mm height. Everything from 0.1mm and below should be alright.

I considered adjusting the model but decided to leave it as is, as I'd rather have a more positive engagement that you can adjust to your liking than end up with one that doesn't latch in place securely enough. I'll leave this marked as a work in...

Don't go bananas with the size of your 50mm fan - there isn't a lot of room to play with; I'd suggest a slimline model for safety. - Print out your Bleh5, any (non-wobbly) material will do. - Note the picture above and glue it to your assembled...

Also there is heavy variance in the quality of the PCB you source from various providers as such various tolerances are required.Prints in 30 minutes in quality modeNo supports requiredNo screws requiredClip on method to assemble itVarious clearance...

Project: Playdough Tool Design Challenge Overview & Background: Through this lesson, students as young as five years old can be introduced to 3-D modeling and desktop fabrication, with an emphasis on its ability to provide solutions to everyday...

The bell is modeled after a large bore 8.5 inch symphonic bell, fitting a Bach 42 or Bach 50 slide, and possibly other brands as well. It's designed to work with a PVC slide, which can be replaced with any type of tube by editing the .scad file...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_bottom_fillet_resolution = 8...

I would recommend all the bridges honestly. Update Jan 31 2021made the holes for the hex nuts smaller to promote better hold under torqueadded relief cut on the M6 hole, as threading may result in splitting the model on version D1resized the D1...

My O scale model train layout represents the section of the Pittsburgh & Lake Erie Railroad between McKees Rocks and Youngstown. This wall section (stretcher bond brick pattern) will let you assemble a background flat of the McKees Rocks...

The rail is just for easy mounting and maintenance. The base is designed to work with the Ender 5 Plus which I have, and should theoretically fit the Ender 5 and maybe other Creality printers too. I uploaded the STEP files too and encourage you to...

They are press fit and held by friction only and on my prints are very secure, they snap in pretty securely but can relatively easily be removed by getting a nail in the seam then wiggling. How I Designed This I created this because I wanted to have...

Merry Christmas! You will need to print: 4 ea Whirligig blades 3 ea Eccentric cams 2 ea Crossbars 2 Reindeer 2 ea Base Couplers 1 ea all other parts There is a cutaway view in the thing files called cutaway view.pdf showing how the model goes...

Printer Settings: * Printer Brand: RepRap * Printer Model: Original Prusa i3 * Rafts: No * Supports: No * Resolution: 0.2mm * Infill Percentage: 25% Print Notes: I utilized a 0.8mm nozzle to expedite the printing process, which took approximately...

Attention, there is V2 as when I was designing this I didn't think about some stuff so I added them, but I didn't print this updated model. I'm only unsure about the switch if the top cover will fit as I think it should.</p> <p>Features:<br/> ...

Print Settings Printer: FlashForge Rafts: No Supports: No Resolution: .2mm (Medium) Infill: 20% Doesn't matter Notes: For the most part, I intended these to print without supports; however, the housing is so wiggly that it needed some once I...

Printing horizontally for increased strength meant the tube experienced a little shrinkage (9% horizontally, 1% vertically), so I made a bigger model (Tube_40mm_account_for_shrinkage.stl) that accounted for this shrinkage, which worked...

All of the parts are assembled with pressure fit slide connections, and I added some vaseline between the parts to make it more airtight and to allow them to more easily come apart for service. I ended up cutting off the top tab on the Here are the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

If you prefer nuts, you have to use longer screws (ca 20 or 25 mm). Box: 4pcs M4x10 DIN912 + T-nuts. 5V Step down converter: 2pcs M3x4 ISO7380. You can use for fixation of the MicroSD extender either attached SDclip model or heat both pins and "melt"...

A short bridge is required for the rail end caps. Post-Printing All holes are intentionally modeled as very tight fits and are intended to be drilled out with a 3mm bit to ensure proper fit. The threaded inserts will push waste material into the...