arduino nano lego 3d models

I used an Arduino Pro Mini running on 5v so I could vary the speed depending on the position of a rotary switch. This fan is noisy when run flat out and you may not need to do this all the time. I'm experimenting. Note: the instructions say the...

Check out my YouTube channel https://www.youtube.com/channel/UC82xXciVxsQKthONKeYbhnw for how to videos about 3d modeling, printing and home automation Update: I've started a series of how-to videos for this project, please check out the full...

You could also go with something else, like an Arduino or ESP32 if you'd prefer to save some money.MagnetsThe lid is held in place by eight bar magnets measuring 25x5x3mm. There's a variety of different sources for magnets like these...

If your tolerances are a little out, and the face isn't tight in the body when the screws are tightened, a couple of drops of superglue at the back edge should be sufficient to tighten the clock face to the diffuser. Ensure all components are...

Just keep in mind that at around 5V, one fan will require about 50 mA (so, not Arduino-friendly unless you run it off the 5V supply directly). If you want to replicate what I did, you'll need the BOM. My project uses 2 fans (combined max. 100 mA @...

The model will consist of: A generic ring segment (printed 20 times or so) Top, Mid, and Bottom tank bulkhead rings Crewed & cargo nose options Engine Mount Ring Landing Gear (someday?) and the various movable control surfaces (at 1:100 scale,...

https://github.com/Hopperpop/Sgp4-Library the firmware was directly inspired by Alex Chang project : (Thanls Alex for sharing ) https://create.arduino.cc/projecthub/alex_chang/satellite-tracker-13a9aa How to do it : Print the dish in two halves (brim...

The wireless side was developed by me and my friend Mika, code is available in GitHub, compile with Arduino + Teensyduino IDE. https://github.com/mtakala/simracing_wireless_buttons Wheel setup Refer to software project git for exact wiring. Each...

I also sorted out a Repetier firmware problem caused by an Arduino issue hanging onto original values in the Eprom. I should have known better than to configure and print for the first time on Friday the 13th! I'm currently using a temporary heated...

It's a standard LCD2004 with a PCF8575 port expander, exactly like those sold for Arduino. ### Keys The Anet LCD2004 uses a resistor network to encode the buttons to one pin. I'm replicating that setup. The rotary encoder emulates the center...

Additionally, you will also need to install the neopixel library from Adafruit in Arduino IDE.Note: In order to get the LEDs to work you will have to use the code attached instead of the one directly from Git Hub. ...If you want to use the one from Git...

For more information see https://blog.prusaprinters.org/watertight-3d-printing-part-2_53638/pbtec / pb-tec.chFor Projects with ESP32, ESP8266, Arduino, Raspberry, Sonoff, Shelly, IoBroker, IoT. In- and outdoor :-)</p><p>Let me see your prints, and...

Here is a link to THE BEST TUTORIAL I HAVE FOUND TO DATE on how to flash firmware onto the Tronxy X5S WITHOUT NEEDING AN ARDUINO UNO. Contrary to popular belief (at least with the new version of the Tronxy X5S) you only need a computer and the USB...

I recently updated the central Arduino board and its standoffs, so the complications involving those should be eliminated. The central board design no longer matches what is shown in the imgur album, but it should still fit since I did not change the...

*Rotary Encoder* https://www.amazon.co.uk/DIFCUL-Degree-Encoder-Development-Arduino/dp/B09P52R8VD This is another awkward sensor, when purchased the pin point outwards and they need to point down to fit in the case. You can unsolder the original...

Part changes (Number to print - Filename - Usage): 1 - frankensnappy_logo.stl - replaces the original logo 1 - heightened_3d_print_extrusion_platform.stl or heightened_3d_print_extrusion_platform_e3d.stl - replaces the original extrusion platform...

The supplied Arduino code is meant to be used with a NodeMCU board which is a Wifi-capable micro controller board based on ESP8266. However the code should also work with ESP32 boards, although not tested. In the code you can change the name of...

#include #include #include "Adafruit_MQTT.h" #include "Adafruit_MQTT_Client.h" #include "FS.h" #include Servo servo; /************************* WiFi Access Point (CHANGE THIS) *********************************/ #define WLAN_SSID "YourSSIDHere"...

Parts List: ESP8266 Card: https://www.amazon.com/gp/product/B081CSJV2V/ 8x8 Matrix LED: https://www.amazon.com/gp/product/B08QN1XDWG/ Jumper Wires: https://www.amazon.com/Elegoo-EL-CP-004-Multicolored-Breadboard-arduino/dp/B01EV70C78 Wire Shrink...

It's Basic language is less intimidating than the Arduino C++ language. It also contains built in commands for reading Sony ir codes. I will include links to the EasyEda schematics and boards for both versions. You can order the boards through...

Download and install Arduino IDE Browse into the Marlin folder and run Marlin.ino In the IDE, under Tools -> Board select Genuino Mega 2560, Processor ATmega2560 and Programmer USBtinyISP Customize if needed (e.g. motor directions and type at line...

Building this extruder requires a bit more effort than previous iterations, but I think it's worth it to avoid opening Arduino every time there's an update. Another feature of this version is a brand-new fan unit that incorporates the fan mount and...

Any amount of support is greatly appreciated :-) paypal.me/BrianBrocken Feel free to take a look at my other designs: 3D printable antweight battlebot: Bulldog: https://www.thingiverse.com/thing:4623536 SpaceX inspired edf rocket:...

I needed a compact all-in-one unit to control my garage doors via ESPHome (Arduino) in Home Assistant and loved estancil's design so much I made the integration of it a basis to build my unit around. Like many projects this quickly developed scope...

IMPORTANT NOTE 2: you need to install a Boards Manager for esp8366 in your development environment (I used Arduino IDE). Initially I tried the latest version, but everything was moving very slowly then and changing the servo speed settings did not...

# Parts: ## Random - Wire (6ft for the staff, but more for various bits) - Hot glue - Super glue - E6000 glue - conformal coating ## Main Staff: - 1x CrystalLEDJig - 1x StaffCrystal - 1x Crown - 1x StaffTop - 9x shaft - ~71" 1" schedule 40 PVC (dirt...

| 10 UDS-1000 Uds DC5V PL9823 F5 5mm F8 8mm Round RGB LED P9823 chipset inside RGB full color LED Chips https://a.aliexpress.com/_BOh3cQ plexiglass sheet for the led screen...

Right now I do not have the funds or ability to do the metal work to make this smaller, for the time being I damaged some LEGO brinks to give me some more space in the back to extend the Y end stop. To give way to over large belt tensioner. Ideally...

Hold down the button for 400ms to skip to the next track.You can change which playlist or video will be played by editing the config file (sudo nano /etc/lofipi-mpv.conf). &nbsp;This file starts out empty, but these are the default settings that will...

White), Blue LED (Green, White), Cooling fan (Red, Black) Raspberry Pi setup The red LED on the top of the wind turbine is connected as an ACT LED on the RPI so it is always flashing when the RPI working. To set up this, you need to add the...