posable 3d model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

To do this, I will add the foot models in STEP format, they are easy to edit. Assembly video: https://www.youtube.com/watch?v=zzjLTr3RoPg https://www.youtube.com/watch?v=Tg764du-zTU https://www.youtube.com/watch?v=Vcvz-GSpdps With a 3S...

Every link piece adds roughly 2,5 cm or 1 inch. Step eight:Cut Filament to 2,3 cm and attach the body strap to Piece K connector strap. Step nine:Cut again Filament to 2,3 cm and attach the N handles to M handle attachment:Congratulation, you just...

# What you'll need This will work with any CH340 USB-serial chip I think, but the model here is for the CH340N for USBC. A picture of the exact chip is given. I ordered one from AliExpress for about $3, and one from eBay for about $6 (because it was...

:DI put 3 holes in the top of the soap container where you can store your toothbrush or similar bathroom itemsI hope you enjoy the model and just try it out for yourself.I have written a description of how to make the soap here, which should give you...

The “NANO 1” model follows (support for matrix / hemera already published). in addition to the name and logo (grant it to me) they share the same "SUPPORT BASE" component as a fixed base, and with the quick release (only 2 screws) to adapt in the...

The automatic transmission in some models has a tendency to fail prematurely. This usually happens around an average mileage of 108,000. **1.1 Identifying Transmission Issues** Transmission failure can be determined through comprehensive...

It features several small niceties, such as a water inlet that optimizes top-water removal, using magnets instead of suction cups, a 'vacation' mod for skimmer waste overflow, snap-on piping for secure fitting, and much more.Please note that this is...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 6 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 custom_case_wall_thickness = 1.6...

If you decrease the size of the model, you will end up with less than 2 layers which might decrease the integrity of the maze. You should be OK increasing the size, but the maze walls may not fuse in the middle using 2 layers. You'll need to...

 900mm in length (shown in the picture is a bit too long, you may want to use 800mm instead)The bamboo skewers seems to come in different sizes, so use the file that closest match the skewers you have and scale the model accordingly.  If...

They should easily fit even on small printers; if you can print Hadley, you can print this mount.The mount uses a vinyl disk that sits on top of teflon pads, for very smooth motion.It is very lightweight, and can easily disassembled for compact...

Update 220811:Added solid with 1deg step on requestReplace the code below to this, (BB and CC changed to 2 and 1 and replace STL to the new...

*Download new version 1.01 here: https://www.printables.com/model/178925-ender-3-s1-stealth-light-bar-easy-to-print-and-do-mod ( Maintaining on Printables ) Easy to print light bar that uses the built in accessory port for power. This allows for...

The retainer is up higher than need be in the video for safety.--------------------------------------------------------------------------------------------------------------All parts printed in PETG, with standard Voron settings for rigidity.0.20...

I was unaware that the MMU2S required changes to the extruder and almost decided to hold off and just install the SPA by itself, but I started poking through the assembly manual for the MMU2S and realized there were changes that needed to be made to...

In short, it means that we will be using the Name Tag creator  to make the base (and thus be able to add text, image files, &c), and then create fitting covers and holders in this program. (A mixed approach is to also create the base with...

... The single-blade model can be reversed in most slicer programs to cut from one side or the other of the 120 film, as described earlier, in "Preparing This Tool." The OpenSCAD source file therefore lacks any provision to make this adjustment. ...

Print instructionsCategory: 3D Printer Parts Summary I've been enjoying using the stock inductive Z endstop as a bed probe on my Artillery Genius, but was suffering a bit from its temperature sensitivity: I was noticing that at different times of...

Also this shape is very special because you can use two V Plate and invert one to create a sort of "wave" that visually connect two I plate that is place up and down.Double C Plate* : This isn't a stand alone plate, this mean this plate is useless on...

... once you have confirmed it's done. You will see just bars on the display only.</p> <p>After that load what ever Firmware you like be it 1.1.9 or 2.0. This will give you a fully clean install, with no hang overs from past FW. Category: 3D Printers

The Gryphon is a mostly 3D printable, hobby-grade, Nerf semi-automatic flywheel blaster. Its main design features are as follows:Uses 130 to 180 sized 20.4mm , brushed DC motors.Semi-auto by rack and pinion with 1:3 gear multiplication. The trigger...

Ich habe mich bemüht alles genau aufzuschreiben, vielleicht habe ich ja aber doch etwas übersehen. Beim ChaosRun handelt es sich um ein kleines 3D gedrucktes LED Spiel für den kleinen oder großen Zeitvertreib und je nach Spiel für bis zu vier...

You have to look very carefully at the top side to see that it is 3D printed. That said, I think I prefer the look of the first version. It is more special with the black part laying on top of the white background.</li></ol><p>Note that the .stl...

Align top frame width from the 200x400 sheet slots if needed.Mark screw locations on the top frame, drill and install screws (M3x16)Add metal rod pieces to the hinge between top frame and front sheetGlue magnets to 28 SL1S enclosure front bottom mid...

Neglecting the losses in the energy transfer, this battery could add 90Wh to my board, which is about 60% of my original Onewheel Pint battery, or rather about 6km of additional range.I designed a 3D printable converter enclosure with two main parts...

... loading filament on each lane to test if the chamfers cut on the smaller tubing is enough to prevent the filament from getting stuck, and to see if the small tubing is seated correctly. Rechamfer/reseat as required Category: 3D Printer Accessories

3D Printing is about beauty and design. When storing the filaments visibly, the storage should at least satisfy some degree of beauty. When designing parts to be printed, you also need to take care of the print process: The print should use as less...

*helps: complicated objects, not designed for 3D printing* **Raft layers** `(2-4)` can not only help with bed adhesion but also can help with technical prints where even first few layers need to be accurate. When you add a raft all the first layer...

I found printing 16 a time eventually one clip would pop off and ruin the batch, the ears add enough bed adhesion to keep any from popping off, and it makes taking the pieces off the bed easier. Comments greatly appreciated, let me know what you...