regular dodecahedron 3d models

To allow for regular enrichment with natural branches (parrots love to chew wood, strip bark, chew on buds and leaves), as well as rotating durable plastic toys, I made this pop-on and pop-off branch mount for little birds. You will have to...

Regular rubber bands seem to be a decent compromise between speed and noise, but a thicker band will quiet it more. There should be no twists in the band when it is installed. It should be possible to pop the reel off later and install the band if...

You will need one of the plates with the hole for your 3/4" tubing used with the wand, one of the "fat plates" for the bottom of the pack, two of the short plates for the top of each side, and ten of the regular plates. You will also need one...

I have ordered some mini-b and regular B breakouts from china and will look into whether they could potentially fit if there is interest. I have also noted that there are two kinds of micro-b breakout boards floating around both my workbench and...

It is held on with a dovetail tapered on one side to apply slight pressure when fully inserted. There are 5 printed components, and at my regular print settings can be printed in under an hour at 100% infill which is useful for parts this small....

You can actually buy a special optically clear glass if you'd like to but I priced it out and it came to about $115 and only in 1/4" thickness, versus about $15 for regular 1/8" glass. *Hardware* * 1x 1.5 x 1/4" bolt * 1x 1.75 x 1/4"...

The fit is fairly snug so be careful when adding and removing accessories.There is a .step file included so you can modify the mount to fit your needs, for example create mounting points and mount an ADXL345 accelerometer to calibrate your X axis...

They are meant to be printed laying down (hence the hex shape) because printing them vertical results in shafts that break at the layer lines regularly. They have a slight detent at each end which holds the Hex Shaft End Caps in place preventing them...

Angled uses angled Talons and straight uses regular straight Talons. Parts tagged with 16mm are for 16 mm OD or Caliburn-spec sized barrels. - SmallSpringStuff/LargeSpringStuff is for picking your spring diameter. SmallSpringStuff is for K26 sized...

Although he continued his regular work, he grew distant, bitter, and often frustrated at his lack of progress. The dreams of a happy family came crashing down when the boys were seven, and Emilia went out one night to look for Jedediah, only to find...

Fan screws might make step 5.2 difficult, but doable with a small screw driver or a right angle screw driver If you’re mounting the GPU to a regular motherboard without any riser cables that mount the GPU upright, then you want the fan blades to be...

I regularly get messages from some of you for the source files. So I released them in the zip-archive called "source" as .ipt (Autodesk Investor) and .stp.</p> <p>Right now I plan on building a wearable version which ist scaled down a little bit so...

This is definitely better than regular CA glue, but there's probably something else even better.Glue one unmodified choc mini switch in the first row. I brush a very light amount of glue on the keywell housing then place the switch in.</li><li>For...

The 055xprob regularly changes hands for €80 on the relevant classifieds exchanges...Anyway... I was now ready to organize the conversion set, but due to tax changes and the like. Due to the lifestyle of the inventor(s), it was no longer so easy to...

When opened from the regular position it will always be empty. To load it, it must be opened from the special slider position. Please be sure to read through the printing and assembly instructions before printing (no really, it'll help prevent...

Regular rubber bands seem to be a decent compromise between speed and noise, but a thicker band will quiet it more. There should be no twists in the band when it is installed. It should be possible to pop the reel off later and install the band if...

Skadis slots enable 3D-printed parts to attach much more securely and reliably than the holes in regular pegboard. The community has created some positively genius ways to interface with Skadis, and I'd like to add another option to the ways you can...

I have reduced it to 245C (Line 79) This is for users that swap different filament types regularly. ie PLA to petg.&nbsp;</p><p>If you are like me and only print with high temp filament ie ABS and PET where the temperature is at 260-270C, enabling...

They thought it silly to worship a god that you cannot see and explained that they regularly visit the lake that “The many-faced god” lives in to bring him sacrifices and to receive his blessing in return. There was going to be another sacrifice the...

I had the most success when printing the model at 75% of regular speed.Print 2 of the "head" models and 2 of the "tail" models to attach to the foot of your MT-24EX flashes to the loc-line with the following settings:Material: PLA or PETGLayer...

Assembly Each carriage is assembled from the following parts: 3D-printed block Eccentric spacer w/ 6mm rise Two (2) 5mm x 11mm x 6.35mm regular spacers Three (3) Mini Kossel 5mm x 21.5mm x 7mm wheels M6 x 12mm x 1.6mm washer, with the hole drilled...

As a result, we had to improvise and revise our plans, utilizing the three point arc tool instead of the regular arc tool as it would allow us to draw arcs with the correct precision required. In addition to this we had to use manual ‘equal’...

Gyroid infill is as good as solid infill for transmitting these shear forces, so that is what I used to save material.With Prusa's powder-coated sheet (which has trouble adhering to PLA), one of the footpad disks lifted off the build surface during...

Example: https://www.youtube.com/watch?v=mRO0wfSQ6jw You don't need to use SMD resistors, the regular wired ones work fine. 3. Install the motor, prop shaft, and rudder shaft tubes. Wick some superglue or epoxy to seal the shaft tubes onto the hull,...

there are several variants including 125mm barrels or 75mm barrels) 1x left grip (there are several grip variants included) 1x right grip 1x hammer arm 1x hammer head 1x hammer spring inner 1x hammer spring outer 1x hand 1x latch_L 1x latch_R 1x...

I use the Nozzle X 0.4. Links: Orbiter Extruder: https://www.thingiverse.com/thing:4725897 (I just bought the ready-to-go Orbiter version from Aliexpress) Fan duct: any regular Predator fan duct would do as long as it stays clear enough of the...

I've printed mine with ABS, and regularly run my bed at 120 degrees C without any issues. To mount these, you will need: - 3 x 400mm 2020 aluminium extrusion - 3 x stock z stepper motors (and appropriate drivers) - 3 x M5/M8 coupling...

• There are two linear rail alignment blocks; the regular one and an extended one that is 3mm longer on one side. The extended side allows you to use it without having to remove the acrylic side covers. Hardware ------------- Linear Rails: •...

For available media keys available for use please go to https://github.com/T-vK/ESP32-BLE-Keyboard[Please not media keys use the write function and regular keys use press]Changes in these 2 places allow to change all the buttons and functions, you...

If you don't need the keychain, just delete the cylinder and you're done. Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: Doesn't Matter Resolution: 0.12 for best adhesion Infill: The higher, the better Filament: Hatchbox...