turning pi 3d models

The hot end fan leaks air like crazy out of the bottom, all around the cold end and build plate, causing loads of problems with PETG and other heat sensitive filaments and warping, even with the part cooling fan turned off. The factory part cooling...

I have tried to save all the SLT's in the orientation they are supposed to be printed (except the plugs I see now, but you can turn them in the slicer, they are just for guiding the two center sections when gluing). In order to minimize possible...

When the weather turns for the worst, the charge connector can quickly get wet/contaminated leading to intermittent charging. There is nothing worse than seeing a "battery low warning" when your legs are already about to give up! ###...

Printing instructions: Each die is positioned in the best printing direction, so don´t turn them in Cura. For all dice set the support overhang angle to 43° and "touching builtplate only. Use high quality setting to get the best possible result...

I only use one bolt and leave the other hole empty.Turn the holder around so the flange is on the bottom. You will need two spring retainers. They will go across the gaps between the pairs of protrusions on the top of the holder.</p><p>Take one...

> - "Remove the cam follower set screw by a few turns to make sure there's room for the cam to rotate" > - "Then put the cam in position 1 and re-tighten the set screw until you feel just a little bit of resistance. Don't torque the set screw at...

There is a 2K resistor in between the Atmega1284p chip and the NPN transistor that runs the fan, which is too high of a resistance to fully turn on the transistor. I bodged in a 220 ohm resistor between the Atmega1284p and the base leg of the...

Note: By turning the stock hot end by 90°, it effectively increases the cooling area from 168 (14mm x 12mm)mm² to 264 (22mm x12mm)mm², an increase of 96 mm², you do the math, and enjoy the benefit of better cooling on the stock heat sink. If you...

Now mark the bolt with a marker so you can avoid accidentally turning it. Since it is so sensitive, you want a line along the length of the bolt that matches a mark on the frame so that any angular motion can be spotted and corrected. Tighten the...

Design a control box to allow each strip to be turned on individually, likely with a dimmer circuit. Modify the Diiicooler to place LEDs around its perimeter. EDIT 16 May 2016: Added a rendering of the work in progress concept for the "foot...

For best results, I'd recommend turning on Ironing in Cura to smooth out the areas where filament can't be printed in the text. This is intended to be printed in three colors, with the filament swapped at the following layers (assuming 0.2mm layer...

Stencils rotation will change this parameter, if desired (set current to 0), in turn affecting stencil placement overall structure as well depending how precise an end product someone desires or needs depending individual preferences here. Since...

I also wanted light so I can turn off lights around the house at night. My setup is a CR-10S Pro with a Wham Bam bed. I removed the original clips that held the original bed and used one of the holes for my mount. I drilled two holes in the magnetic...

Make sure the wheels turn easily but can not slip. Assemble the hotend with the cooling parts to the Hotend_Bracket (by following the instructions of https://www.thingiverse.com/thing:2763931, although any order should work with these parts). ...

It turned out that the issue was the spacing between the rods. The carriage moved easily in the centre of the rods as there was enough flex to allow movement but as the carriage moved up towards the top of the rods, where they are held in position...

To change the taking lens, turn the GrabLocker counter-clockwise, push the scope away, switch lenses, push it back, lock and load :) ADDENDUM Follwing is a detailed description for all the parts provided GrabLocker This integral part locks the scope...

If you use a recess at the bottom of the box, you can turn on the "support on build plate only" when this recess is wide. <a href="https://help.prusa3d.com/article/insert-pause-or-custom-g-code-at-layer_120490">Insert a pause</a> at the beginning of...

this model is based on real data therefore this is a realistic buildings and streets setup of Tbilisi, Georgia 6 building groups are setup so that you can add variety to buildings (color materials and/or textures) Groups can be turned off/on UV...

After that, turn the cover forwards (toward its closed position), applying a bit of force (though not enough to break the model). This should break the supports inside the axle holes and allow the axle to rotate freely. If the print still doesn't...

The side door can also open and lock as you turn the door handle, small model hinges are required for this to function. Polycarbonate sheets can be cut according to the included .DXF files and can be mounted in the grooves, which function as the...

The tightening knob should be on the build plate with the threaded end pointing upwards.Let the build plate cool before removing to prevent warping the sealing surfaces.If the build plate is flexible, flex it in 2 directions by turning the build...

* Front mounting with PSU intake facing the inside of the case leads to the PSU eating hot GPU exhaust, which in turn led to my PSU being the loudest component in the case... * If memory serves, the official design wasn't quite meant being mounted...

Keep thin features turned on. Onyx will work even better than straight nylon, I will try that soon, they accidentally shipped us two rolls of nylon with the printer instead of one each. ... How I Designed This Remixed from the v3 bottom frame stl file...

this model is based on real data therefore this is a realistic buildings and streets setup of Nagasaki, Japan 5 building groups are setup so that you can add variety to buildings (color materials and/or textures) Groups can be turned off/on UV mapped...

*\*I'm not sure what kind of power the FT140-43 can take; I'm only ever putting up to 20W into it, and it seems to handle that without issue.* # Features - Circular shaped wire winder keeps wire bends smooth and even preventing sharp turns/bends...

There needs to be a spot in the cotton where the oil is thin enough to evaporate easily: this is where the cotton will turn black, and where the combustion occurs. A butane barbecue lighter works well, with the arm to get to the inside of the...

Turning an illustration/logo into a 3D model can be quite tricky, but I figured I could do a decent job while still capturing the all-important whimsy of the logo. In the original illustration, I spent loads of time playing with proportions and...

... care of the problem. (i.e. They might have to be sideways or facing backwards compared to the other minis.) This was my first custom project, so I'm sure it's not perfect, but I'm pleased with how it turned out, and hope others find it useful too!

The motors turn in opposite directions, so there is no choice about the mounting unless you modify the firmware or the plate. If you use the mixing hot end like Geeetech uses, you also need a mounting plate between the hot end and the carriage...

... The effector plate and magnet holder (if you use it) needs to be turned upside down. The fan shim and cable tidy should lay down flat. The fan mount can be printed as it is. The fan mount and the magnet holder should be printed with supports. ...